Some will advise that that has a ball powder You will need a magnum primer or mil spec primer.  That is just an previous wives tale!

His loads are actually effectively analyzed and used by others for in excess of 25 a long time. Depart a Reply Cancel reply

Horn, I've tried 50gr. H380 for the 165gr Hor. awhile back, fifty two currently being the max. but you truly have to pack that bullet in there Together with the max load, but I did get pretty good precision with it, three/four" @100 I believe it was, from the 700V, but if you do not treatment about fitting the round as part of your mag.(solitary shot) seat the bullet about .010' off the lands like I reported prior to plus the bullet will not be so packed in there so limited, which I guess truly Never damage very little, so long as it goes in.

Scott Rupp gets a chance to talk to Aaron Oelger about a couple of new products from Hodgdon and why reloading keep cabinets are empty.

 My load with Hornady 55-gr bullets was fine, but his Using the Noslers (inside of a Rem 700 VS) was not.  Warm temps + a bullet that tends to produce a lot more pressure + unique rifle.  Backing off not less than 0.5 to twenty five.5 or much less would address his pressure troubles. In the case of somebody making use of Federal .223 Rem brass that's been mentioned for creating pressure problems on account of It really is thicker walls and thinner World-wide-web spot, a lessened load is absolutely advisable. This is certainly why some posters have diverse final results with loads that are merely fantastic for Other people. The majority of handloaders who may have no way of chronographing their operate-ups like a strategy for getting a manage on stress inside their guns with their elements.  When strain signals seem on the brass and/or primer, then sadly abnormal stress is already current.  Keeping track of the chronograph ordinary velocities lets you realize when expected optimum velocity has actually been arrived at.  In cases like this It will be in the region of 3107 fps if you common out all five resources.    As a result backing off a tad will Commonly stay clear of this which is making use of good sense. One great way of acquiring a fantastic handle on what your restrictions ought to be is always to average data from the many resources you may get.   In this case, averaging all five resources presents an average most demand fat of 25 grains at 3107 fps. In case you were being to throw out the "odd" highest charge weight of Hornady as well as the "odd" minimal velocity of Sierra you would get this normal: twenty five.five grains at 3134 fps - which I do think could well be somewhat extra practical figures for barrels within the twenty-22" vary from what I have seen. That is certainly why I like to consult as numerous data sources as you possibly can just before setting goals for the load do the job-up.  Also, just one need to research and find out if the preferred parts can incorporate to tension (Federal .223 brass, Nosler Ballistic Ideas, M193 bullets and many others.)   Certainly this discussion isn't about acquiring your "accuracy node" but just cost/force/velocity objectives or ceilings.  On the other hand in my case, precision seems to raise with improves in cost fat when loading H-335.  Start out loads like 23 to twenty five grains are only so-so, but loads like twenty five.5 are Great for me.  I believe that the bullet used tends to make A much bigger variation than the charge fat. *While some Take note that 26.0 grains is often a "5.fifty six NATO-tension" load - in this specific case it is clear that real five.fifty six NATO-pressure ammo - LC M193 actually is much hotter and 90 fps a lot quicker With this certain AR15.  This may only be set up through the chronograph or even a pressure barrel.  

There may be some differences in the internal construction among the TAC traces and the other Barnes strains. Physically, I am unable to evaluate any distinctions amongst the 22406 and the 22460. I have acquired a number of each sitting on my shelf.

+1  Actually I carried the feeling in my sigline for half a year. Genuinely, foolish lazy jargon suggests a air of sloppiness that does not bode nicely with the treatment of handloading.  Properly that is my emotions about the matter.  To every his individual although.

At the moment each powder cost is weighed on a Hornady scale right before I seat the bullet. I make use of a Lee single phase push and I haven't been reloading long enough to have confidence in the powder spouts for bodyweight so it really is a a person phase at a time affair. All over again, many thanks for all the enter here. You could never ever have more than enough awareness. Simply click to grow...

It shoots terrific but is filthy and as stated gets incredibly hot in the summertime. For me I like Tac and AR COMP much better. As of these days I switched to Varget for .308/.223.

× Like a bolt gun, an AR has challenging Bodily capabilities, but the look and operation tend to be more complex. In possibly a bolt motion or an AR, the chamber and bore could be Reduce restricted or loose. On the other hand, in immediate-impingement ARs, the gas port diameter And the way significantly it’s Found alongside the barrel are mounted.

Spherical powders want that added shot through the magnum for reputable ignition, at least that's the theory. I have generally applied 400's in all my guns, including with my ARs and have never had a challenge both.

Add to quote Only exhibit this consumer #15 · Sep 8, 2016 I remember a newer means of chasing ocw was loading one more past max. If you do not have any tension spikes, then it was proposed to go yet one more stage to discover if you will get a lot more velocity for very long selection focusing on.

Furthermore, ammunition organizations haven't any control above how cartridges are saved, including rattling close to on a pickup’s dashboard h335 reloading data in the course of summertime warmth, which can nearly always elevate pressures when fired. Nonetheless, most loads approached advertised velocity figures recognized from 24-inch exam barrels when fired in the Ruger M77 Hawkeye’s 22-inch barrel.

I necessary to locate a speedier means of loading, that’s Once i started out making use of H335. I'd the same success you probably did, working with an RCBS powder measure, my costs we’re normally inside 0.1 grain. Using H335 I utilised thrown rates completely.